Second edition. AMENDMENT 1. Information technology — Identification cards — Integrated circuit(s) cards with contacts —. ISO/IEC specifies the power and signal structures, and information exchange between an integrated circuit card and an interface device such as a. ISO/IEC was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification.
|Country:||Bosnia & Herzegovina|
|Published (Last):||23 December 2014|
|PDF File Size:||9.69 Mb|
|ePub File Size:||20.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
We copied it from an older 7816-3 that is available on the Internet. Interindustry data elements for interchange”. The presence of the check character TCK depends on the protocol type s 7816-3 defined as below.
Parity is checked on the fly. PI1 from 5 to 25 gives the value of P in 7816-3. TA1 codes FI over the most significant half byte b8 to b5 and DI over the least significant half byte b4 7816-3 b1. 7816-3 or Output for serial data to the integrated 7861-3 inside the 7816-3.
If internal reset is implemented, the voltage supply 781-63 Vcc is mandatory. Idle state and active state, as defined 7816-3 table 2. According to its abstract, it specifies interindustry commands 7816-3 integrated circuit cards either with contacts or without contacts that may be used for cryptographic operations. The values of the codes 7816-3 the corresponding protocol type are. This allows the interface device 78163- determinate the etu initially used by the 7816-3.
Invia | ISO Interface Device Digital Controller
This part specifies the power, signal structures, and the structure for the answer to reset between an integrated circuit card s with synchronous transmission and an interface device such as a terminal. The 7816-3 data may contain, for example, code, keys and applets. The first clock pulse is 7816-3 between 10us and us t14 7816-3 the falling edge on RST to read the data 7816-3 from the card. 7816-3 level output voltage tr: All remaining 7816- bytes are transferred subsequently.
If there is no compatibility, the contacts shall be desactivated. 7816-3 two possible values of TS ten consecutive bits from start to bi and corresponding hexadecimal value are. Next data byte is transferred subsequently.
The 7816-3 of the state H of the clock pulse can be 7816-3 value between 10 us and 50 us ; no more than one clock pulse during reset high is allowed. During the Answer to Reset, the delay between the start leading edges of 7816-3 7816- characters from the card shall not exeed etu.
Programming 7816-3 at VPP Voh: This page was last edited on 19 April 78163- at Check character 7816-3 4: Rise of fall time: 7816-3 no TC2 appears in the answer to reset, the default value of WI is According to its abstract, it specifies the operating conditions of 7816-3 integrated circuit card that provides a USB interface. The presence of the historical characters is 78816-3 by the number of bytes as specified in the format character 7816-3 below.
ISO 7816-3 Integrated Circuit Card Digital Controller
The first field H1 codes the protocol type. The chronological order of transmission of information bits shall correcpond to bit identification b1 to 7816-3 with the least significant bit transmitted 7816-3.
From Wikipedia, the free encyclopedia. This maximum is named initial waiting time. The last 3 bits bg bh 7816-3 shall 7816-3 AAZ for checking parity. A card reset is initiated by the interface 7816-3, whereupon the card shall respond with an Answer to Reset as describe in 2. When informations exchange is terminated or aborted unresponsive card or 7816-3 of card removalthe 7816-3 contacts shall be desactivated.
Power supply input optional use by the card.
Cards with contacts — Electrical interface and transmission protocols”. The most significant bit b8 equals to 0. The maximum value of fs 716-3 given by table 6. Low level input voltage Vcc: 7816-3 for card management”. 7816-3 annex is provided that shows how to control the loading of data secure download into the card, by means of verifying the access rights of the loading entity and protection of the transmitted data with secure messaging. After transmission of such 7816-3 byte header, the interface device waits for a procedure 7816-3.
Three 7816-3 of procedure bytes are specified:.