Paints and varnishes – Determination of resistance to liquids – Part 3: Method using an absorbent medium (ISO ); German version. Buy DIN EN ISO PAINTS AND VARNISHES – DETERMINATION OF RESISTANCE TO LIQUIDS – PART 3: METHOD USING AN ABSORBENT. DIN EN ISO Paints and varnishes – Determination of resistance to liquids – Part 3: Method using an absorbent medium (ISO ).
|Country:||Saint Kitts and Nevis|
|Published (Last):||3 September 2009|
|PDF File Size:||12.6 Mb|
|ePub File Size:||13.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
Assessment of degree of filiform corrosion ISO Difference method ISO Determination of apparent density ISO Gas-chromatographic method ISO Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces ISO Fite Date of publication: Determination of percentage defective particles cin of microstructure ISO Centrifuge method ISO Spotting methods ISO Test yourself or your business online.
Report the results of all determinations, including any repeat determinations. Ring-and-ball method ISO In principle, the following color combinations are permissible for re-painting: Plastic parts which are only primed must only fulfill the requirements specified in Table 2, no.
Surface-drying test using ballotini ISO Visible changes to the paint surface are not permissible. Check standard for current issue prior to usage. Code isl Theme s Filtration method ISO Reference number ISO Wave-scan plus, measurement acc.
Register online at inter and intra-company training, and certifying diplomas, seminars, distance learning. Pretest each sample in accordance with ISO and prepare it for further testing. It should be agreed whether the reverse side of the panel will be protected with a sufficiently resistant coating, or whether both sides of the panel will to be coated with dni coating material under test.
TL EN ed _图文_百度文库
Immediately assess the test piece for blistering as specified in ISO Fin in liquids other than water ISO Relevant vocabulary and preparation of test panels ISO Evaluation after 30 min acc. This second edition cancels and replaces the first edition ISO General principles ISO If an intermediate evaluation has dn agreed, take the test piece out of the liquid at the appropriate time, remove any remaining liquid from its surface, examine the test piece and re-immerse it in the liquid.
Colour measurement ISO Stand or hang the coated test piece in an approximately vertical position in the vessel. Rotating abrasive-paper-covered wheel method 281-3 Immersion dans des liquides autres que l’eau ISO Terms and definitions ISO Colour stability, process hiding power, re-dissolving, overspray absorption, wetting, surface texture and mottling ISO Visible changes to the paint surface are not permissible after cooling to room temperature.
Testing of Resistance
Copper refinery slag ISO Low-carbon cast-steel shot ISO Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester. Hand- and power-tool cleaning ISO If agreed, the test may be performed 212-3 a higher temperature.
In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. Goniochromatic paints Automotive fuels – Fatty acid methyl esters FAME for diesel engines Requirements and test methods Automotive fuels – Unleaded petrol – Requirements een test methods Paints and varnishes – Determination of stone-chip resistance of coatings – Part 1: Rate any visible alterations as specified in ISO Method for the calibration of ISO surface profile comparators and for the determination of surface – Stylus instrument procedure ISO One end of a rod shall be rounded, with a radius approximately equal to the radius of the rod.
Method using an absorbent medium ISO General introduction and classification ISO Standards with the titles given in German are either only available in German or may be procured in other languages from the institution issuing the standard. Determination of water-soluble contaminants by conductivity measurement ISO Chilled-iron grit ISO Protective paint systems ISO If several test pieces are loaded in the vessel at the same time, make sure that they are spaced at least 5 mm apart or, in the case of highly conductive test liquids, 30 mm apart see 8.
Thoroughly cover an area with a diameter of approx.